RVs, campers and vans
RV Fresh Water Tank Sanitizing - Bleach by Tank Size, the Wait and the Flush
Updated October 12, 2026 - 4 min read - Rainy Day Plan
The short answer
To sanitize an RV fresh water tank, take out the filters, then pour in 1/4 cup of plain liquid household bleach for every 15 gallons the tank holds. Fill it with water and pump it to every hot and cold faucet until you smell bleach. Let it sit 2 to 4 hours, then drain and flush until the smell is gone.
How much bleach for your tank size
Use 1/4 cup of liquid household bleach for every 15 gallons of tank. Find your tank's size on the spec sheet or in the owner's manual, then read across.
| Fresh tank | Bleach |
|---|---|
| 15 gallons | 1/4 cup |
| 20 gallons | 1/3 cup |
| 30 gallons | 1/2 cup |
| 40 gallons | 2/3 cup |
| 45 gallons | 3/4 cup |
| 50 gallons | 3/4 cup plus 4 teaspoons |
| 60 gallons | 1 cup |
| 75 gallons | 1 1/4 cups |
| 100 gallons | 1 2/3 cups |
For a size that isn't listed, divide the gallons by 60 and you have the cups. Say your tank holds 36 gallons, as an example: 36 divided by 60 is 0.6 cup, a bit more than 1/2 cup.
This rate is for cleaning the tank. It isn't the one for treating water you plan to drink; that's in how to purify water.
Plain bleach only
Buy regular, unscented chlorine bleach whose label says it's for disinfecting and sanitizing. Leave the scented kinds on the shelf, along with bleach made for colored fabrics and bleach with added cleaners. Splash-less bleach is out too: it has thickeners in it and less of the active chemical.
Turn the jug around and the label will say 6 or 8.25 percent sodium hypochlorite. The table works with either. At 8.25 percent, the same 1/4 cup makes the mix a bit over a third stronger than at 6 percent, so plan on one more flush at the end.
The steps, from empty tank to clean water
- Drain the fresh tank and flush it once with clean water.
- Take out every water filter cartridge and any purification gear, including a filter on the hose at the tap. They go back in after the last flush.
- Look at the water heater bypass. If it's still set from winter, put it back to normal so the bleach water goes through the heater and out the hot side too. Leave the heater switched off until it's full of water. If your owner's manual says to keep the heater out of this job, go by the manual.
- Measure the bleach from the table and pour it into the fresh tank's fill. Stirring it into a jug of water first makes it easier to pour without splashing. If your rig fills only through a hose hookup, with no opening to pour into, pour the mix into the end of the fill hose with a funnel, then connect it and fill.
- Fill the tank with fresh water. Then drive around the block so the mix sloshes over the inside walls of the tank.
- Turn the pump on. Open each faucet, hot side and cold side, until you smell bleach there, then close it. Go through the kitchen, the bathroom sink, the shower, the toilet and the outside faucet or shower.
- Switch the pump off and leave the bleach in the system for 2 to 4 hours.
- Drain the tank, and open the faucets and the low-point drains to empty the lines. Drain the water heater too (it's still off): it holds bleach water, and emptying it now saves flush rounds.
- Close the low-point drains and put the water heater's plug back. Refill, take another short drive, then run fresh water through every faucet, hot and cold, and the toilet, and drain again. This is the slow part. Keep going until there's no bleach smell left at any faucet.
- Put the filter cartridges back in.
When a bleach taste hangs on
You're done when no faucet smells of bleach. If you still smell it at one, do one more round of fill, drive and drain.
If the chlorine taste in water you've already drawn is too strong, pour it from one clean container to another and let it stand for a few hours before you use it.
How often the tank needs it
Sanitize the fresh tank and the lines:
- when the rig is new to you, used or brand new, since you don't know what sat in that tank before
- after it's been parked in storage
- right after de-winterizing, once the pink antifreeze is flushed out (the fall steps that come before this)
- when the water smells off, feels slimy, or a water test comes back bad
- after you've filled up from a tap you weren't sure about
Tie it to those moments rather than to a calendar. For a rig that's stored every winter, that means at least once a year, at the spring opening.
Questions people ask
Can we use the tap while the bleach is in the lines?
Not for drinking, cooking or brushing teeth. Keep the faucets closed through the 2 to 4 hours, don't use anything that runs out while you flush, and drink from stored water until the smell is gone. A few jugs will see you through the afternoon, and emergency water storage lays out how to keep them.
How long does the whole job take?
Plan on most of an afternoon. The bleach sits 2 to 4 hours, and then come the drain, the refill, the drives and at least one more round. A big tank on a slow hose takes longer, so start in the morning if you want to sleep with clean water in the lines.
Sources
Every number in this article comes from these public sources, and we checked each one before it went up.




































